H125/H151/H200M/H200/H300 Multi-Media Filter Systems
WATER QUALITY
BACK
DIMENSIONS 1
EST.
CF
WASH
SHIP
MODEL PIPE FILTER TANK SUPERIOR HIGH UTILITY FLOW TOTAL INLET OUTLET DRAIN WIDTH WT.
SIZE MEDIA SIZE
RATE
H 2
I
O
D
W
LBS.
H125-MM10-1
1.25
1
10X44
4
7
9
8
51
46
46
57
11
190
H125-MM10-1.5
1.25
1.5
10X54
4
7
9
8
63
57
57
58
11
224
H125-MM13-2
1.25
2
13X54
7
11
14
14
63
57
57
58
14
312
H125-MM14-3
1.25
3
14X65
9
13
16
16
74
68
68
69
15
443
H125-MM16-4
1.25
4
16X65
11
17
21
20
74
67
70
68
17
624
H125-MM18-5
1.25
6
18X65
14
21
26
25
76
68
71
69
19
720
H151-MM14-3
1.5
3
14X65
9
13
16
16
74
68
69
70
15
453
H151-MM16-4
1.5
4
16X65
11
17
21
20
74
68
69
70
17
584
H151-MM18-5
1.5
6
18X65
14
21
26
25
76
69
70
71
19
730
H151-MM21-6
1.5
7
21X62
19
29
36
35
72
65
67
67
22
856
H200M-MM14-3
2
3
14X65
9
13
16
16
78
69
69
78
15
468
H200-M-MM16-4
2
4
16X65
11
17
21
20
78
69
69
78
17
649
H200M-MM-18-5
2
5
18X65
14
21
26
25
80
71
71
80
19
745
H200M-MM-21-6
2
6
21X62
19
29
36
35
80
71
71
80
22
886
H200M-MM-24-8
2
8
24X72
25
38
47
45
88
79
79
88
25
1405
H200-MM-24-8 3
2
10
24X72
25
38
47
45
89
83
87
85
25
1410
H200-MM30-15 3
2
15
30X72
39
59
74
75
86
80
84
82
31
2040
H200-MM-36-20 3
2
20
36X72
56
85
106
105
87
81
85
83
37
2620
H300-MM-36-20 3
3
20
36X72
56
85
106
105
104
96
96
100
37
2720
H300-MM-42-30 3
3
30
42X72
77
115
144
145
109
102
102
104
43
3580
1 All dimensions are ± 1”
2 Allow additional 12” for media loading
3 Available in top-mount or side-mount
  • Service and backwash flow rates are based on 50ºF incoming
    • water temperature.
  • Operating parameters - pressure range 40-100 PSI; temperature
    • range 40º-110ºF.
  • Product improvement designs are subject to change without notice
    • As a general rule - Lower flows produce higher quality water and a
    larger volume of treated water between backwashing.
    Superior
  • Recommended for most filtering applications under all operating
    • conditions. 8 gpm/ft 2
  • Best quality water
  • Maximum time on line between backwashing
  • Lowest pressure loss
    • H125
    H151
    H200M
  • Recommended for influent suspended solids loads up to and
    • greater than 300 ppm.
    Consult ’s engineering department for additional sizes, modifi -
    cations or special applications.
    High
  • Well suited for many filtering applications. 12 gpm/ft 2
  • Very good quality water
  • Moderate time on line between backwashing
  • Increased pressure loss
  • Recommended for influent suspended solids loads less than 300
    • ppm.
    Utility
  • Flow rates listed are at peak design - operation at higher flow rates
    • not recommended. 15 gpm/ft 2
  • Satisfactory water quality
  • Shorter on line time
  • Higher pressure loss
  • Recommended for influent suspended solids loads less than 150
    • ppm.
    Media: Anthracite, Filter Sand, Garnet and Support Bed.
    1-800-626-1417
    www..com
    800311
    2/12 - LBRY
    ©2009-2012